When is a 2.4 GHz access point the better path?

Use the 2.4 GHz SLIM architecture with a compatible Cedar V3 access point when the project needs centralized wireless updates, larger multi-store control, or explicit AP coverage planning — typically larger chains. Keep this path separate from TagHub BLE.

Can one phone replace an access point for SDR labels?

No. SDR / 2.4 GHz SLIM labels are updated through the access-point architecture. BLE labels use the phone workflow. Do not mix the two label families in messaging or assume one phone covers full-store SDR updates.

ESL architecture · decision page

Access point or BLE? Start with TagHub BLE.

Q: Should most small stores start with BLE or an access point?

Tocvue’s default recommendation is TagHub BLE with a phone or tablet local workflow. No access point is required for that basic local workflow. Confirm model and app behavior before ordering.

Tocvue offers two separate ESL architectures. For most small stores, phone shops, boutiques, and pilots, the default is TagHub BLE — phone or tablet local updates without an access point for the basic workflow. Keep the HonorLink / 2.4 GHz AP path as a secondary option when a large chain truly needs centralized control.

Conclusion: Start with TagHub BLE + TagHub App (coming soon). Bring in Cedar V3 / 2.4 GHz SLIM only when the buyer clearly needs multi-store centralized AP updates.

Two paths — keep them separate

Use the checklist below to choose. Battery years, IP ratings, and interference claims are confirmed per model in writing — not invented on this page.

Default · recommended

TagHub BLE (phone workflow)

Bluetooth ESL labels managed with a compatible phone or tablet app for the basic local workflow. No access point is required for that basic workflow.

Best fit: small shops, 3C / phone stores, boutiques, pilots
Staff must be near the label to trigger a refresh
Pair with TagHub App (coming soon) for Tocvue’s BLE story
Do not promise unattended full-store auto-pricing on BLE alone

TagHub App → · BLE-213BWRY →

Secondary · large chains

2.4 GHz SLIM + Cedar V3 AP

Centralized wireless updates through a compatible Cedar V3 access point (AP / gateway) for SLIM-series labels. Ordinary Wi-Fi APs are not a substitute for the ESL access point.

Best fit: larger chains that need centralized / multi-store control
Requires AP coverage planning and project confirmation
POS / ERP sync is a project requirement — confirm, do not assume
Keep messaging separate from TagHub BLE

ESL overview →

Side-by-side (buyer checklist)

High-level comparison only — confirm exact model, app, quantity and integration in writing.

Question	TagHub BLE (default)	2.4 GHz AP (secondary)
Who updates the label?	Phone / tablet near the label	Compatible Cedar V3 access point
AP required for basic local use?	No	Yes
Typical starting scenario	Small store / pilot / boutique	Large chain / centralized control
Unattended full-store auto change	Not the BLE default story	Project-dependent with AP + platform
Mix with the other label family?	Do not mix SDR and BLE messaging; confirm SKUs with Tocvue / IT before quoting mixed floors
Battery years / IP65 on this page?	Not stated — confirm per model; do not invent

Important: BLE refresh needs the phone in Bluetooth range and a staff trigger in the app. SDR / 2.4 GHz labels cannot be refreshed by phone Bluetooth. TagHub is Tocvue’s BLE app name for this path.

How to decide in one minute

Default: choose TagHub BLE + TagHub App.
Only if you are a large chain that needs centralized AP control → look at 2.4 GHz SLIM + Cedar V3.
Confirm in writing battery life, solar options, local protocols, and IP ratings for the exact SKU.
Do not mix AP and BLE into one interchangeable system.

Not sure which ESL path fits?

Share store count, label quantity, and whether staff can walk the floor with a phone. Tocvue will recommend TagHub BLE or the AP architecture — not both mixed into one pitch.

Request guidance